ARK Dual Power Trailer Socket 7Flat Pin 50A Connector
7 Pin & Anderson Connections!
16% OFFRRP $49.95
$42.00
$329.95
EBRAKES Guardian with PEB12-7 Adapter
This is a complete DIY kit comprising of a totally proportional electric trailer brake control, wiring loom & trailer adapter enabling the brake unit to be used as a portable device with no hard wiring required. Simply plug into your 12v cig lighter socket and run the leads to the supplied 7 pin to 12 pin trailer plug and your ready to tow any caravan, camper or trailer with electric brakes.
This kit contains a Hayman Reese Guardian timed brake controller brake control unit and is the most cost effect product.
Fitment
This unit can be mounted in any position.
- Securely mount the brake controller as shown above.
- Connect the 4 wire plug to the back of the brake unit.
- Connect the cigarette power plug to the vehicles 12v socket.
- Run the 5m length of cable with the 2 pin connector from the brake unit to the rear of the vehicle feeding the cable through a safe path.
- Drop the lead out of the boot lid and connect the 2 pin connector plug to the supplied adapter.
(diagram b) Caution, Do not pinch or damage the cable during this process. - Connect the supplied trailer adapter to the vehicle & connect the trailer. (diagram c)
- Turn on vehicles ignition and follow the OEM instruction manual to set the power setting to 5.0 by holding the manual override fully to the left & rotate the power knob.
- Test brakes at a stand still position by applying the manual override while a secondary person listens to the trailer wheels to ensure the electronic brake magnets are operating.
You should hear a buzzing noise coming from the trailer wheel hubs as brake power is applied.
To test braking level is suitable for your towing weight drive the tow vehicle and trailer on a dry level & solid surface at roughly 40kph and fully apply the manual override.
- If the brakes lock up, turn the adjustment control to a lower setting
- If the braking was not sufficient, turn the adjustment control to a higher setting
Repeat the tow brake test until the adjustment control is set at a point just below trailer wheel lock up.
Package Contents:
1 x Guardian Timed brake controller
1 x Power & connection cables
1 x Adapter 12pin flat female to 7pin flat male (additional adapters available on request)
Instruction manual
WARNINGS
Only compatible with vehicles that operate with 12v power
ENSURE THAT YOUR TRAILER BRAKES ARE INSTALLED AND OPERATING CORRECTLY. IMPROPERLY INSTALLED OR FAULTY TRAILER BRAKES CAN CAUSE ERRATIC VEHICLE OR TRAILER BEHAVIOR WITH POTENTIAL TO CAUSE A ROAD ACCIDENT. ALWAYS CHECK BRAKES AT LOW SPEED EACH TIME A TRAILER IS CONNECTED TO YOUR VEHICLE.
DUE TO BEING A PORTABLE DEVICE OPERATING FROM A 12V CIGARETTE LIGHTER SOCKET THE UNIT IS LIMITED TO BRAKING EITHER A SINGLE AXLE OR TANDEM AXLE TRAILER ONLY. IT IS NOT SUITABLE TO OPERATE BRAKES ON A TRIPLE AXLE TRAILER UNLESS THE UNIT IS HARD WIRED AS PER THE SUPPLIED INSTALLATION INSTRUCTIONS.
CAUTIONS
- If towing a tandem axle trailer it is recommended that you use a 12v 15amp cigarette socket as your power source if 100% braking force is required. If a 15amp power source is not available you can operate the unit from a 10amp socket under limitations as noted in diagram a. This is to prevent the possibility of the vehicles cigarette lighter socket fuse blowing upon 100% braking force being applied if the unit is set too high while being powered from a 10amp socket.
- It is recommended that while using your portable electric brake unit that you do not operate or charge any other devices from another power source in your vehicle unless that power source is isolated from the cigarette lighter socket which is providing power to your brake unit.
This product is supplied to allow ease of fitment in vehicles that require a non-permanent installation. All mounting orientation and operational requirements in the Brake Controller manufacturers product manual still apply, and must be followed to ensure safe operation.
Road rules relating to towing vary between Australian State jurisdictions. It is advisable to check the trailer brake requirements in your state to ensure that you are fully compliant with local regulations.
Includes:
1 x Hayman Reese Guardian Timed Brake Controller
1 x WL001 Portable Wiring Loom
1 x PEB12-7 Trailer Adapter (12pin flat to 7 pin flat to vehicle)
1 x Spare Fuse
1 x Instruction Card
| SKU | PEB004 |
| Brand | EBRAKES |
| Shipping Weight | 1.2000kg |
| Unit Of Measure | ea |
Be The First To Review This Product!
Help other Award RV Superstore users shop smarter by writing reviews for products you have purchased.
Others Also Bought
12pin Flat to Trailer - 7pin Flat to Vehicle
Compatible with any EBRAKE portable electric brake kits.
$49.95
12pin Flat to Trailer - 7pin Flat to Vehicle with Anderson Socket
Compatible with any EBRAKE portable electric brake kits.
$79.95